Raising the close force on the opener can stop the reversal, and it also stops your door from reversing off a child, a pet or a car bumper. Leave the settings as they are and keep the opening clear until the reversal has a diagnosis.
Service · Carrollton, TX
Garage Door Reverses Before Closing in Carrollton, TX
Your garage door reverses before closing: it travels most of the way down, touches or nearly touches the floor, then goes back up. A door that reverses near the floor reads resistance as an obstacle, from a close-force setting, a down-travel limit set too low, or a door that binds on the last stretch. Keep the opening clear and call about your Carrollton garage before anyone turns up the force to make it close.
What you are seeing
Down most of the way, then back up
Auto-reverse sends your door back up when it meets resistance on the way down. With nothing under the door, that resistance comes from the door itself, the floor or the opener's settings.
- Down limit too low
The opener keeps driving after the door reaches the floor, reads the floor as an obstacle and reverses.
- Close force too low
The setting can't push your door through ordinary friction near the bottom.
- Binding near the bottom
A bent lower rail, a dry hinge or a worn roller adds drag on the last stretch.
- Early floor contact
A swollen or bunched bottom seal, or a high spot on the slab, meets the door before the opener expects it.
Keep the opening clear and leave the opener's force setting alone, then call about why it reverses.
(972) 634-8789Loss risk
What a reversing door risks
A door that won't finish closing leaves your garage open, and the obvious workaround makes it dangerous.
- Open behind you
You press the button in the car, drive off, and the door climbs back up after you leave.
- Crush protection lost
Turning up close force to stop the reversal lets the door press down on whatever it meets.
- Repeated cycles
Each reversal runs the opener and the lower rollers through another full trip.
- Hidden drag
Binding that triggers a reversal today is the same wear that jams the door later.
Safety protocol
Leave the force setting alone
Repair scope
How diagnosis finds the reversal
Diagnosis separates a setting fault from a door fault, because adjusting settings on a binding door only hides the problem.
- Force and limit
Close force and down travel match your door's actual weight and the floor.
- Drag check
Your door runs off the opener to reveal binding in the lower rail, rollers or hinges.
- Floor and seal
The bottom seal and the slab show whether the door meets the floor early or unevenly.
- Reverse test
Auto-reverse has to trip on contact with an object on the floor.
Service sequence
From a reversing door to a full close
Opening clear
You keep the opening clear and stop trying to force a close.
Cause separated
Diagnosis splits setting faults from drag in the door.
Drag removed
Binding rollers, hinges or a bent lower rail come back into line.
Settings matched
Force and down travel fit your door and the floor.
Close confirmed
Your door seats on the floor, stays down, and still reverses on contact.
Local detail
When the door goes back up after you drive off
A door that reverses after you leave your Carrollton driveway stays open until you come home. If yours has done it once, watch it seat on the floor before you pull away, and call about the reversal.
Triage order
Why a door that won't finish closing needs the call
Each time your door turns around at the floor, the garage stays open and the drag behind it keeps wearing the door. Call from Carrollton or surrounding Dallas County while the cause is still a setting or a roller, and before anyone turns the force up.
Service area
Carrollton ZIP codes
- 75006
- 75007
- 75010
- 75011
Every responding technician is independent. Before work begins, confirm the technician's license, insurance and pricing with them directly.
Common questions
Questions about a door that reverses in Carrollton
Why does the door touch the floor and go back up?
The opener is still driving when your door meets the floor, so it reads the floor as an obstacle. A down limit set too low or a door that binds near the bottom causes it.
Is a door that reverses before closing a sensor problem?
Not usually. A safety eye fault turns the door around soon after it starts down; a reversal at the floor comes from force, travel or drag.
Can a new bottom seal stop the reversal?
Sometimes. A bunched or swollen seal meets the floor early, but if the cause is drag or settings, a seal alone won't stop it.
A door held by a broken spring is a door waiting to drop.
Call from Carrollton before a broken spring or cable strips the opener or bends the sections.